Punqtum Q210 P | Intercoms Base Station | Intercoms

4-Channel Intercom Station, Built-in PoE switch for power up to 8 beltpacks

Speaker Station gives you full control in a cost-effective and easy-to-use package.
4 Channel communication, and programmable buttons allow muting all mics, make paging announcements or trigger logic outputs.
Equipped with a network switch with 4 ports.
Two of them are PoE powered to drive up to 4 wired beltpacks each.
The Q210 P Speaker Station is your complete, self-contained communication hub.

- 4-channel partyline speaker station
- Built in loudspeaker
- Microphone and headset connector
- Rugged, Ethercon? connectors
- Easy-to-read colour display
- 4 configurable buttons for PA announcements, talk to all, and GPO
- Audio replay of missed comms
- GPI inputs and outputs
- Analogue inputs/outputs (2x 4-wire ports + 2x inputs + 2x outputs)
- Built-in PoE switch to power up to 8 beltpacks
- 2 Public address output
- 2 Program signal inputs
- On- and Offline configuration software (Win/ Mac)

General
Power Source: 50 ? 54 VDC
PoE Power: 30W per PoE port
Sampling Rate: 16 kHz
Headset Connector: XLR 4pin male
Connector Ethernet/LAN: 4x RJ-45 EtherCon
Microphone Connector: 1/4" jack with 7/16" -20 UNF thread
Built-in Speaker: 5 Watts
Operating Temp.: -10° to +50°C
Operation Environment Humidity: 0 to 90% non-condensing
H x W x D: 19" 1HU: 100 x 433 x 44 mm
Weight: 1.7 kg

Headphone Output
Output impedance: 27 Ohm
Output level: + 18.5 dBu (max.)
Frequency response: 20Hz to 7kHz (+0/-1dB)
Distortion @ 1kHz: <-73 dB (0.02%)
Dynamic range (20kHz): 95 dB (A-weighted)

Microphone Input
Bias Voltage: 5.4V (typ.)
Full-scale input range: 53 ? +4 dBu
Distortion @ 1kHz:
< -75 dB (0.02%) @ + 4dBu FS (min. gain)
< -68 dB (0.04%) @ -30dBu FS
< -49 dB (0.35%) @ -53dBu FS (max. gain)
Dynamic range:
- 92 dB (min. gain)
- 59 dB (max. gain)

Analog Interface Outputs
Input Impedance: < 2 Ohm
Input Level: + 18 dBu (max.)
Frequency Response: 20Hz to 7kHz (+0/-0.25dB)
Distortion @ 1kHz: <-80 dB (0.01%)
Dynamic Range (20kHz): 98 dB (A-weighted)

Analog Interface Inputs
Input Impedance: > 20 kOhm
Input Level: + 18 dBu (max.)
Frequency Response: 20Hz to 7kHz (+0/-0.25dB)
Distortion @ 1kHz: <-80 dB (0.01%)
Dynamic Range (20kHz): 90 dB (A-weighted)

GPI Inputs
Input Connector: D-Sub 9 female
Number of GPI Inputs: 4
Input Type: Optocoupler input with current limiter
Input Voltage: 5 ? 50 VDC
Input Current: 5 mA (typ.)

GPI Outputs
Output Connector: D-Sub 9 male
Number of GPI Outputs: 4
Output Type: PhotoMOS Relay
On Resistance: < 3 Ohm
On Current: 200 mA (max.) - resettable PTC fuse 400 mA
Maximum Voltage: 50 VDC / 35 VAC
(*) all specifications are subject to change without notice

Q210 P - Punqtum

Accessories for Q210 P

Others customers also ordered

Best selling